Biblio

Communication systems across a variety of applications are increasingly using the angular domain to improve spectrum management. They require new sensing architectures to perform energy-efficient measurements of the electromagnetic environment that can be deployed in a variety of use cases. This paper presents the Directional Spectrum Sensor (DSS), a compressive sampling (CS) based analog-to-information converter (CS-AIC) that performs spectrum scanning in a focused beam. The DSS offers increased spectrum sensing sensitivity and interferer tolerance compared to omnidirectional sensors. The DSS implementation uses a multi-antenna beamforming architecture with local oscillators that are modulated with pseudo random waveforms to obtain CS measurements. The overall operation, limitations, and the influence of wideband angular effects on the spectrum scanning performance are discussed. Measurements on an experimental prototype are presented and highlight improvements over single antenna, omnidirectional sensing systems.

This paper presents the synthesis and circuit transformations of acoustic wave filters based on a transversal arrangement of the individual resonators. This configuration allows for the synthesis of any filter response without detrimental of the limited value of the electro-acoustic coupling coefficient. The synthesis can be performed in the low-pass domain to be latter transformed into the band-pass domain. This latter step results in significant differences between the low-pass and the band-pass responses in wideband stringent filters. This work, after an initial synthesis in the low-pass domain, directly applies the pass-band circuit transformation achieving a more accurate synthesized network even for wideband filters.

Radio-frequency identification (RFID) has become a preferred technology for monitoring in industrial internet of things (IIoT) applications like supply chain, medical industry, vehicle tracking and warehouse monitoring where information is required continually. Typical security threats seen in these applications are denial of service (DOS) attack, transmission attack etc. We propose a novel edge data security schema based on spike modulation along with backscatter communication technique to modulate both sensor and identification (ID) information. It is observed that this data encoding schema works well even in a multi-tag single-reader environment. Further, it uses lower power and offers a low-cost solution for Industrial IoT applications.

This paper presents a proximity coupled wideband wearable antenna operating between 4.71 GHz and 5.81 GHz with 5.2 GHz as centre frequency for biomedical telemetry applications in ISM band (IEEE 802.11 Standard). Two layers of different flexible substrate materials, ethylene-vinyl acetate and felt make the design mechanically stable. Bandwidth improvement is achieved by introducing two slots on elliptical ground plane. Highest gain of 3.72 dB and front to back ratio (FBR) of 6.55 is obtained in the given frequency band. The dimensions of antenna have been optimized to have desired bandwidth of 1100 MHz (\$\textbackslashtextbackslashsimeq\$21%). The specific absorption rate (SAR) value is 1.12 \$W/Kg\$ for 1 g of human body tissue. Both simulated and measured results are presented for the structure.

Cognitive Radio is a prominent solution for effective spectral resource utilization. The rapidly growing device to device (D2D) communications and the next generation networks urge the cognitive radio networks to facilitate wideband spectrum sensing in order to assure newer spectral opportunities. As Nyquist sampling rates are formidable owing to complexity and cost of the ADCs, compressive sampling approaches are becoming increasingly popular. One such approach exploited in this paper is the Modulated Wideband Converter (MWC) to recover the spectral support. On the multiple measurement vector (MMV) framework provided by the MWC, threshold based Orthogonal Matching Pursuit (OMP) and Sparse Bayesian Learning (SBL) algorithms are employed for support recovery. We develop a Graphical User Interface (GUI) that assists a beginner to simulate the RF front-end of a MWC and thereby enables the user to explore support recovery as a function of Signal to Noise Ratio (SNR), number of measurement vectors and threshold. The GUI enables the user to explore spectrum sensing in DVB-T, 3G and 4G bands and recovers the support using OMP or SBL approach. The results show that the performance of SBL is better than that of OMP at a lower SNR values.

To experimentally study the characteristics of ultrasonic sensors, a wideband air-coupled ultrasonic transducer, wideband electromagnetic dynamic acoustic transducer (WEMDAT), is designed and fabricated. Characterisation methods, including electrical impedance analysis, laser Doppler vibrometry and pressure-field microphone measurement, are used to examine the performance of the WEMDAT, which have shown that the transducer has a wide bandwidth ranging approximately from 47 kHz to 145 kHz and a good directivity with a beam angle of around 20˚ with no evident side lobes. A 40 kHz commercial flexural ultrasonic transducer (FUT) is then taken as an example to receive ultrasonic waves in a pitch-catch configuration to evaluate the performance of the WEMDAT as an acoustic source. Experiment results have demonstrated that the WEMDAT can maintain the most of the frequency content of a 5 cycle 40 kHz tone burst electric signal and convert it into an ultrasonic wave for studying the dynamic characteristic and the directivity pattern of the ultrasonic receiver. A comparison of the dynamic characteristics between the transmitting and the receiving processes of the same FUT reveals that the FUT has a wider bandwidth when operating as an ultrasonic receiver than operating as a transmitter, which indicates that it is necessary to quantitatively investigate the receiving process of an ultrasonic transducer, demonstrating a huge potential of the WEMDAT serving as a standard acoustic source for ultrasonic sensors for various air-coupled ultrasonic applications.

This paper presents a model calibration algorithm for the modulated wideband converter (MWC) with non-ideal analog lowpass filter (LPF). The presented technique uses a test signal to estimate the finite impulse response (FIR) of the practical non-ideal LPF, and then a digital compensation filter is designed to calibrate the approximated FIR filter in the digital domain. At the cost of a moderate oversampling rate, the calibrated filter performs as an ideal LPF. The calibrated model uses the MWC system with non-ideal LPF to capture the samples of underlying signal, and then the samples are filtered by the digital compensation filter. Experimental results indicate that, without making any changes to the architecture of MWC, the proposed algorithm can obtain the samples as that of standard MWC with ideal LPF, and the signal can be reconstructed with overwhelming probability.