Biblio

Tamper detection circuits provide the first and most important defensive wall in protecting electronic modules containing security data. A widely used procedure is to cover the entire module with a foil containing fine conductive mesh, which detects intrusion attempts. Detection circuits are further classified as passive or active. Passive circuits have the advantage of low power consumption, however they are unable to detect small variations in the conductive mesh parameters. Since modern tools provide an upper leverage over the passive method, the most efficient way to protect security modules is thus to use active circuits. The active tamper detection circuits are typically probing the conductive mesh with short pulses, analyzing its response in terms of delay and shape. The method proposed in this paper generates short pulses at one end of the mesh and analyzes the response at the other end. Apart from measuring pulse delay, the analysis includes a frequency domain characterization of the system, determining whether there has been an intrusion or not, by comparing it to a reference (un-tampered with) spectrum. The novelty of this design is the combined analysis, in time and frequency domains, of the small variations in mesh characteristic parameters.

Security protection is a concern for the Internet of Things (IoT) which performs data exchange autonomously over the internet for remote monitoring, automation and other applications. IoT implementations has raised concerns over its security and various research has been conducted to find an effective solution for this. Thus, this work focus on the analysis of an asymmetric encryption scheme, AA-Beta (AAβ) on a platform constrained in terms of processor capability, storage and random access Memory (RAM). For this work, the platform focused is ARM Cortex-M7 microcontroller. The encryption and decryption's performance on the embedded microcontroller is realized and time executed is measured. By enabled the I-Cache (Instruction cache) and D-Cache (Data Cache), the performances are 50% faster compared to disabled the D-Cache and I-Cache. The performance is then compared to our previous work on System on Chip (SoC). This is to analyze the gap of the SoC that has utilized the full GNU Multiple Precision Arithmetic Library (GMP) package versus ARM Cortex-M7 that using the mini-gmp package in term of the footprint and the actual performance.

The use of a very wide windows operating system is undeniably also followed by increasing attacks on the operating system. Universal Serial Bus (USB) is one of the mechanisms used by many people with plug and play functionality that is very easy to use, making data transfers fast and easy compared to other hardware. Some research shows that the Windows operating system has weaknesses so that it is often exploited by using various attacks and malware. There are various methods used to exploit the Windows operating system, one of them by using a USB device. By using a USB device, a criminal can plant a backdoor reverse shell to exploit the victim's computer just by connecting the USB device to the victim's computer without being noticed. This research was conducted by planting a reverse shell backdoor through a USB device to exploit the victim's device, especially the webcam and microphone device on the target computer. From 35 experiments that have been carried out, it was found that 83% of spying attacks using USB devices on the Windows operating system were successfully carried out.

Wearable medical devices are playing more and more important roles in healthcare. Unlike the wired connection, the wireless connection between wearable devices and the remote servers are exceptionally vulnerable to malicious attacks, and poses threats to the safety and privacy of the patient health data. Therefore, wearable medical devices require the implementation of reliable measures to secure the wireless network communication. However, those devices usually have limited computational power that is not comparable with the desktop computer and thus, it is difficult to adopt the full-fledged security algorithm in software. In this study, we have developed an efficient authentication and encryption protocol for internetconnected wearable devices using the recognized standards of AES and SHA that can provide two-way authentication between wearable device and remote server and protection of patient privacy against various network threats. We have tested the feasibility of this protocol on the TI CC3200 Launchpad, an evaluation board of the CC3200, which is a Wi-Fi capable microcontroller designed for wearable devices and includes a hardware accelerated cryptography module for the implementation of the encryption algorithm. The microcontroller serves as the wearable device client and a Linux computer serves as the server. The embedded client software was written in ANSI C and the server software was written in Python.

This paper presents BackFlow, a compiler-based toolchain that enforces indirect backward edge control flow integrity for low-end ARM Cortex-M microprocessors. BackFlow is implemented within the Clang/LLVM compiler and supports the ARM instruction set and its subset Thumb. The control flow integrity generated by the compiler relies on a bitmap, where each set bit indicates a valid pointer destination. The efficiency of the framework is benchmarked using an STM32 NUCLEO F446RE microcontroller. The obtained results show that the control flow integrity solution incurs an execution time overhead ranging from 1.5 to 4.5%.

Small embedded devices such as microcontrollers have been widely used for identification, authentication, securing and storing confidential information. In all these applications, the security and privacy of the microcontrollers are of crucial importance. To provide strong security to protect data, these devices depend on cryptographic algorithms to ensure confidentiality and integrity of data. Moreover, many algorithms have been proposed, with each one having its strength and weaknesses. This paper presents a Differential Power Analysis(DPA) attack on hardware implementations of Advanced Encryption Standard(AES) running inside a PIC18F2420 microcontroller.

Distinguishing and classifying different types of malware is important to better understanding how they can infect computers and devices, the threat level they pose and how to protect against them. In this paper, a system for classifying malware programs is presented. The paper describes the architecture of the system and assesses its performance on a publicly available database (provided by Microsoft for the Microsoft Malware Classification Challenge BIG2015) to serve as a benchmark for future research efforts. First, the malicious programs are preprocessed such that they are visualized as gray scale images. We then make use of an architecture comprised of multiple layers (multiple levels of encoding) to carry out the classification process of those images/programs. We compare the performance of this approach against traditional machine learning and pattern recognition algorithms. Our experimental results show that the deep learning architecture yields a boost in performance over those conventional/standard algorithms. A hold-out validation analysis using the superior architecture shows an accuracy in the order of 99.15%.

Recent controlled-channel attacks exploit timing differences in the rudimentary fetch-decode-execute logic of processors. These new attacks also pose a threat to software on embedded systems. Even when Trusted Execution Environments (TEEs) are used, interrupt latency attacks allow untrusted code to extract application secrets from a vulnerable enclave by scheduling interruption of the enclave. Constant-time programming is effective against these attacks but, as we explain in this paper, can come with some disadvantages regarding performance. To deal with this new threat, we propose a novel algorithm that hardens programs during compilation by aligning the execution time of corresponding instructions in secret-dependent branches. Our results show that, on a class of embedded systems with deterministic execution times, this approach eliminates interrupt latency side-channel leaks and mitigates limitations of constant-time programming. We have implemented our approach in the LLVM compiler infrastructure for the San-cus TEE, which extends the openMSP430 microcontroller, and we discuss applicability to other architectures. We make our implementation and benchmarks available for further research.

The Internet of Things (IoT) aims to introduce pervasive computation into the human environment. The processing on a cloud platform is suggested due to the IoT devices' resource limitations. High latency while transmitting IoT data from its edge network to the cloud is the primary limitation. Modern IoT applications frequently use fog computing, an unique architecture, as a replacement for the cloud since it promises faster reaction times. In this work, a fog layer is introduced in smart vital sign monitor design in order to serve faster. Context aware computing makes use of environmental or situational data around the object to invoke proactive services upon its usable content. Here in this work the fog layer is intended to provide local data storage, data preprocessing, context awareness and timely analysis.

Embedded Systems - the hidden computers in our lives - are deployed in the billionths and are already in the focus of attackers. They pose security risks when not tested and maintained thoroughly. In recent years, fuzzing has become a promising technique for automated security testing of programs, which can generate tons of test inputs for a program. Fuzzing is hardly applied to embedded systems, because of their high diversity and closed character. During my research I want tackle that gap in fuzzing embedded systems - short: “Embedded Fuzzing”. My goal is to obtain insights of the embedded system during execution, by using common debugging interfaces and hardware breakpoints to enable guided fuzzing in a generic and widely applicable way. Debugging interfaces and hardware breakpoints are available for most common microcontrollers, generating a potential industry impact. Preliminary results show that the approach covers basic blocks faster than blackbox fuzzing. Additionally, it is source code agnostic and leaves the embedded firmware unaltered.

Automobiles provide comfort and mobility to owners. While they make life more meaningful they also pose challenges and risks in their safety and security mechanisms. Some modern automobiles are equipped with anti-theft systems and enhanced safety measures to safeguard its drivers. But at times, these mechanisms for safety and secured operation of automobiles are insufficient due to various mechanisms used by intruders and car thieves to defeat them. Drunk drivers cause accidents on our roads and thus the need to safeguard the driver when he is intoxicated and render the car to be incapable of being driven. These issues merit an integrated approach to safety and security of automobiles. In the light of these challenges, an integrated microcontroller-based hardware and software system for safety and security of automobiles to be fixed into existing vehicle architecture, was designed, developed and deployed. The system submodules are: (1) Two-step ignition for automobiles, namely: (a) biometric ignition and (b) alcohol detection with engine control, (2) Global Positioning System (GPS) based vehicle tracking and (3) Multisensor-based fire detection using neuro-fuzzy logic. All submodules of the system were implemented using one microcontroller, the Arduino Mega 2560, as the central control unit. The microcontroller was programmed using C++11. The developed system performed quite well with the tests performed on it. Given the right conditions, the alcohol detection subsystem operated with a 92% efficiency. The biometric ignition subsystem operated with about 80% efficiency. The fire detection subsystem operated with a 95% efficiency in locations registered with the neuro-fuzzy system. The vehicle tracking subsystem operated with an efficiency of 90%.

This work focuses on the design and implementation of a microcontroller for apply all the knowledge acquired during Engineering Electronics career. In order to improve the knowledge about RF technologies, security system have been created, which increases the number of applications used in these days. This design utilizes light sensors as the end device for detecting any changes of resistance. The results show that the designed system can send and receive data until 100 meters of distance between module sides (receiver-transmitter). This security system designed using PIC 16F84 microcontroller as entire brain of the system with sensors, has been successfully designed and implement considering some factors such as economy, availability of components and durability in the design process.

Home automation is an intelligent, functional as a unit system that facilitates home processes without unnecessarily complicating the user's life. Devices can be connected, which in turn connect and talk through a centralized control unit, which are accessible via mobile phones. These devices include lights, appliances, security systems, alarms and many other sensors and devices. This paper presents the design and implementation of a Bluetooth based smart home automation system which uses a Peripheral interface controller (PIC) microcontroller (16F1937) as the main processer and the appliances are connected to the peripheral ports of the microcontroller via relays. The circuit in the project was designed in Diptrace software. The PCB layout design was completed. The fully functional smart home prototype was built and demonstrated to functional.

In view of the problem that the health status and safety monitoring of the traditional intelligent home are mainly dependent on the manual inspection, this paper introduces the intelligent home-based remote monitoring system by introducing the Internet-based Internet of Things technology into the intelligent home condition monitoring and safety assessment. The system's Android remote operation based on the MVP model to develop applications, the use of neural networks to deal with users daily use of operational data to establish the network data model, combined with S3C2440A microcontrollers in the gateway to the embedded Linux to facilitate different intelligent home drivers development. Finally, the power line communication network is used to connect the intelligent electrical appliances to the gateway. By calculating the success rate of the routing nodes, the success rate of the network nodes of 15 intelligent devices is 98.33%. The system can intelligent home many electrical appliances at the same time monitoring, to solve the system data and network congestion caused by the problem can not he security monitoring.

The paper considers, proposes and describes possibilities and ways for application, design and implementation of energy efficient microprocessor based embedded systems for LED lighting control in the traffic. Using LED lighting technology and appropriate designed embedded systems it is possible to implement very efficient and smart systems for very wide range of applications in the traffic. This type of systems can be widely used in many places in the traffic where there is needed quality lighting and low energy consumption. Application of such systems enables to increase energy consumption efficiency, quality of lighting and security of traffic and to decrease total costs for the lighting. Way of design and use of such digital embedded system to effectively increase functionality and efficiency of lighting in the traffic is proposed and described. It is also proposed and described one practically designed and implemented simple and universal embedded system for LED lighting control for many applications in the traffic.

This project develops a face recognition-based door locking system with two-factor authentication using OpenCV. It uses Raspberry Pi 4 as the microcontroller. Face recognition-based door locking has been around for many years, but most of them only provide face recognition without any added security features, and they are costly. The design of this project is based on human face recognition and the sending of a One-Time Password (OTP) using the Twilio service. It will recognize the person at the front door. Only people who match the faces stored in its dataset and then inputs the correct OTP will have access to unlock the door. The Twilio service and image processing algorithm Local Binary Pattern Histogram (LBPH) has been adopted for this system. Servo motor operates as a mechanism to access the door. Results show that LBPH takes a short time to recognize a face. Additionally, if an unknown face is detected, it will log this instance into a "Fail" file and an accompanying CSV sheet.

To enhance the encryption and anti-translation capability of the information, we constructed a five-dimensional chaotic system. Combined with the Lü system, a time-switched system with multiple chaotic attractors is realized in the form of a digital circuit. Some characteristics of the five-dimensional system are analyzed, such as Poincare mapping, the Lyapunov exponent spectrum, and bifurcation diagram. The analysis shows that the system exhibits chaotic characteristics for a wide range of parameter values. We constructed a time-switched expression between multiple chaotic attractors using the communication between a microcontroller unit (MCU) and field programmable gate array (FPGA). The system can quickly switch between different chaotic attractors within the chaotic system and between chaotic systems at any time, leading to signal sources with more variability, diversity, and complexity for chaotic encryption.

Memory corruption vulnerabilities, mainly present in C and C++ applications, may enable attackers to maliciously take control over the program running on a target machine by forcing it to execute an unintended sequence of instructions present in memory. This is the principle of modern Code-Reuse Attacks (CRAs) and of famous attack paradigms as Return-Oriented Programming (ROP) and Jump-Oriented Programming (JOP). Control-Flow Integrity (CFI) is a promising approach to protect against such runtime attacks. Recently, many CFI-based solutions have been proposed, resorting to both hardware and software implementations. However, many of these solutions are hardly applicable to microcontroller systems, often very resource-limited. The paper presents a generic, portable, and lightweight CFI solution for bare-metal embedded systems, i.e., systems that execute firmware directly from their Flash memory, without any Operating System. The proposed defense mixes software and hardware instrumentation and is based on monitoring the Control-Flow Graph (CFG) with an FPGA connected to the CPU. The solution, applicable in principle to any architecture which disposes of an FPGA, forces all control-flow transfers to be compliant with the CFG, and preserves the execution context from possible corruption when entering unpredictable code such as Interrupt Services Routines (ISR).

Internet of Things (IoT) is experiencing significant growth in the safety-critical applications which have caused new security challenges. These devices are becoming targets for different types of physical attacks, which are exacerbated by their diversity and accessibility. Therefore, there is a strict necessity to support embedded software developers to identify and remediate the vulnerabilities and create resilient applications against such attacks. In this paper, we propose a hardware security vulnerability assessment based on fault injection of an embedded application. In our security assessment, we apply a fault injection attack by using our clock glitch generator on a critical medical IoT device. Furthermore, we analyze the potential risks of ignoring these attacks in this embedded application. The results will inform the embedded software developers of various security risks and the required steps to improve the security of similar MCU-based applications. Our hardware security assessment approach is easy to apply and can lead to secure embedded IoT applications against fault attacks.

Microcontroller-based embedded systems have become ubiquitous with the emergence of IoT technology. Given its critical roles in many applications, its security is becoming increasingly important. Unfortunately, MCU devices are especially vulnerable. Code reuse attacks are particularly noteworthy since the memory address of firmware code is static. This work seeks to combat code reuse attacks, including ROP and more advanced JIT-ROP via continuous randomization. Previous proposals are geared towards full-fledged OSs with rich runtime environments, and therefore cannot be applied to MCUs. We propose the first solution for ARM-based MCUs. Our system, named HARM, comprises a secure runtime and a binary analysis tool with rewriting module. The secure runtime, protected inside the secure world, proactively triggers and performs non-bypassable randomization to the firmware running in a sandbox in the normal world. Our system does not rely on any firmware feature, and therefore is generally applicable to both bare-metal and RTOS-powered firmware. We have implemented a prototype on a development board. Our evaluation results indicate that HARM can effectively thaw code reuse attacks while keeping the performance and energy overhead low.

Smart home is one application of the pervasive computing branch of science. Three categories of smart homes, namely comfort, healthcare, and security. The security system is a part of smart home technology that is very important because the intensity of crime is increasing, especially in residential areas. The system will detect the face by the webcam camera if the user enters the correct password. Face recognition will be processed by the Raspberry pi 3 microcontroller with the Principal Component Analysis method using OpenCV and Python software which has outputs, namely actuators in the form of a solenoid lock door and buzzer. The test results show that the webcam can perform face detection when the password input is successful, then the buzzer actuator can turn on when the database does not match the data taken by the webcam or the test data and the solenoid door lock actuator can run if the database matches the test data taken by the sensor. webcam. The mean response time of face detection is 1.35 seconds.

Nowadays, safety systems are an important feature for modern vehicles. Many accidents would have been occurred without them. In comparison with older vehicles, modern vehicles have a much better crumple zone, more airbags, a better braking system, as well as a much better and safer driving behaviour. Although, the vehicles safety systems are working well in these days, there is still space for improvement and for adding new security features. This paper describes the implementation of an Intelligent Caravan Monitoring System (ICMS) using the Controller Area Network (CAN), for the communication between the vehicle’s electronic system and the trailer’s electronic system. Furthermore, a comparison between the communication technology of this paper and a previous published paper will be made. The new system is faster, more flexible and more energy efficient.

As demonstrated recently, Wireless Physical Layer Security (WPLS) has the potential to offer substantial advantages for key management for small resource-constrained and, therefore, low-cost IoT-devices, e.g., the widely applied 8-bit MCU 8051. In this paper, we present a WPLS testbed implementation for independent performance and security evaluations. The testbed is based on off-the-shelf hardware and utilizes the IEEE 802.15.4 communication standard for key extraction and secret key rate estimation in real-time. The testbed can include generically multiple transceivers to simulate legitimate parties or eavesdropper. We believe with the testbed we provide a first step to make experimental-based WPLS research results comparable. As an example, we present evaluation results of several test cases we performed, while for further information we refer to https://pls.rub.de.

{In the last few decades, Internet of things (IOT) is one of the key elements in industrial revolution 4.0 that used mart phones as one of the best technological advances' intelligent device. It allows us to have power over devices without people intervention, either remote or voice control. Therefore, the “Smart Radar Door “system uses a microcontroller and mobile Bluetooth module as an automation of smart door lock system. It is describing the improvement of a security system integrated with an Android mobile phone that uses Bluetooth as a wireless connection protocol and processing software as a tool in order to detect any object near to the door. The mob ile device is required a password as authentication method by using microcontroller to control lock and unlock door remotely. The Bluetooth protocol was chosen as a method of communication between microcontroller and mobile devices which integrated with many Android devices in secured protocol}.

This paper emphasizes the implementation of a conditioning circuit specific for an inductive or capacitive sensor. There are some inductive sensors, such as the proximity sensor, for which the inductance is dependent with the distance, or capacitive sensors strongly dependent with the humidity, distance, etc. This category of sensors is suitable for AC domain excitation from the measurement procedure point of view. Taking into consideration the fabrication technology, the measured physical quantity is being encoded as frequency or amplitude. To generate a sinusoidal signal with constant frequency and amplitude, the Colpitts or Hartley oscillators can be used [1], [2]. But the novelty of this paper is a different approach which reveals a microcontroller-based technology where the LC circuit works in an oscillating regime even though there is an underdamped oscillation behavior. For the oscillations’ occurrence, there will be a periodical energy injection using a driving source. One of the main advantages of the mentioned circuit is the small component number. The central unit of the embedded system will fulfil two functions: maintains the oscillating regime and measures the amplitude or frequency of the output signal. In this way, the built embedded system will be robust and easy to use due to its software configuration capabilities. As a plus, such a system can measure additional sensors used in environment parameters’ compensating procedure.