Biblio

The digital low dropout regulators are widely used because it can operate at low supply voltage. In the digital low drop-out regulators, the high sampling frequency circuit has a short setup time, but it will produce overshoot, and then the output can be stabilized; although the low sampling frequency circuit output can be directly stabilized, the setup time is too long. This paper proposes a two sampling frequency circuit model, which aims to include the high and low sampling frequencies in the same circuit. By controlling the sampling frequency of the circuit under different conditions, this allows the circuit to combine the advantages of the circuit operating at different sampling frequencies. This shortens the circuit setup time and the stabilization time at the same time.

The need for performing deep neural network inferences on resource-constrained embedded devices (e.g., Internet of Things nodes) requires specialized architectures to achieve the best trade-off among performance, energy, and cost. One of the most promising architectures in this context is based on massive parallel and specialized cores interconnected by means of a Network-on-Chip (NoC). In this paper, we extensively evaluate NoC-based deep neural network accelerators by exploring the design space spanned by several architectural parameters including, network size, routing algorithm, local memory size, link width, and number of memory interfaces. We show how latency is mainly dominated by the on-chip communication whereas energy consumption is mainly accounted by memory (both on-chip and off-chip). The outcome of the analysis, thus, pushes toward a research line devoted to the optimization of the on-chip communication fabric and the memory subsystem for performance improvement and energy efficiency, respectively.

Wide bandgap power semiconductors are key enablers for increasing the power density of switch-mode power supplies. However, they require new gate drive technologies. This paper examines and characterizes a fabricated gate-driver in a class-E resonant inverter. The gate-driver's total area of 1.2mm2 includes two high-voltage transistors for gate-driving, integrated complementary metal-oxide-semiconductor (CMOS) gate-drivers, high-speed floating level-shifter and reset circuitry. A prototype printed circuit board (PCB) was designed to assess the implications of an electrostatic discharge (ESD) diode, its parasitic capacitance and package bondwire connections. The parasitic capacitance was estimated using its discharge time from an initial voltage and the capacitance is 56.7 pF. Both bondwires and the diode's parasitic capacitance is neglegible. The gate-driver's functional behaviour is validated using a parallel LC resonant tank resembling a self-oscillating gate-drive. Measurements and simulations show the ESD diode clamps the output voltage to a minimum of -2V.

Reliability of electronic devices in sub-nanometer technology scale has become a major concern. However, demand for battery operated low power, high performance devices necessitates technology scaling. To meet these contradictory design goals optimization and reliability must be performed simultaneously. This paper proposes by integrating compiler driven transformation and simulated annealing based optimization process for generating optimized low cost transient fault tolerant DSP core. The case study on FIR filter shows improved performance (in terms of reduced area and delay) of proposed approach in comparison to state-of-art transient fault tolerant approach.

Hardware implementations of cryptographic algorithms may leak information through numerous side channels, which can be used to reveal the secret cryptographic keys, and therefore compromise the security of the algorithm. Power Analysis Attacks (PAAs) [1] exploit the information leakage from the device's power consumption (typically measured on the supply and/or ground pins). Digital circuits consume dynamic switching energy when data propagate through the logic in each new calculation (e.g. new clock cycle). The average power dissipation of a design can be expressed by: Ptot(t) = α · (Pd(t) + Ppvt(t)) (1) where α is the activity factor (the probability that the gate will switch) and depends on the probability distribution of the inputs to the combinatorial logic. This induces a linear relationship between the power and the processed data [2]. Pd is the deterministic power dissipated by the switching of the gate, including any parasitic and intrinsic capacitances, and hence can be evaluated prior to manufacturing. Ppvt is the change in expected power consumption due to nondeterministic parameters such as process variations, mismatch, temperature, etc. In this manuscript, we describe the design of logic gates that induce data-independent (constant) α and Pd.

State-of-the-art convolutional neural networks (ConvNets) are now able to achieve near human performance on a wide range of classification tasks. Unfortunately, current hardware implementations of ConvNets are memory power intensive, prohibiting deployment in low-power embedded systems and IoE platforms. One method of reducing memory power is to exploit the error resilience of ConvNets and accept bit errors under reduced supply voltages. In this paper, we extensively study the effectiveness of this idea and show that further savings are possible by injecting bit errors during ConvNet training. Measurements on an 8KB SRAM in 28nm UTBB FD-SOI CMOS demonstrate supply voltage reduction of 310mV, which results in up to 5.4× leakage power reduction and up to 2.9× memory access power reduction at 99% of floating-point classification accuracy, with no additional hardware cost. To our knowledge, this is the first silicon-validated study on the effect of bit errors in ConvNets.

Embedded electronic devices and sensors such as smartphones, smart watches, medical implants, and Wireless Sensor Nodes (WSN) are making the “Internet of Things” (IoT) a reality. Such devices often require cryptographic services such as authentication, integrity and non-repudiation, which are provided by Public-Key Cryptography (PKC). As these devices are severely resource-constrained, choosing a suitable cryptographic system is challenging. Pairing Based Cryptography (PBC) is among the best candidates to implement PKC in lightweight devices. In this research, we present a fast and energy efficient implementation of PBC based on Barreto-Naehrig (BN) curves and optimal Ate pairing using hardware/software co-design. Our solution consists of a hardware-based Montgomery multiplier, and pairing software running on an ARM Cortex A9 processor in a Zynq-7020 System-on-Chip (SoC). The multiplier is protected against simple power analysis (SPA) and differential power analysis (DPA), and can be instantiated with a variable number of processing elements (PE). Our solution improves performance (in terms of latency) over an open-source software PBC implementation by factors of 2.34 and 2.02, for 256- and 160-bit field sizes, respectively, as measured in the Zynq-7020 SoC.

Near-sensor data analytics is a promising direction for internet-of-things endpoints, as it minimizes energy spent on communication and reduces network load - but it also poses security concerns, as valuable data are stored or sent over the network at various stages of the analytics pipeline. Using encryption to protect sensitive data at the boundary of the on-chip analytics engine is a way to address data security issues. To cope with the combined workload of analytics and encryption in a tight power envelope, we propose Fulmine, a system-on-chip (SoC) based on a tightly-coupled multi-core cluster augmented with specialized blocks for compute-intensive data processing and encryption functions, supporting software programmability for regular computing tasks. The Fulmine SoC, fabricated in 65-nm technology, consumes less than 20mW on average at 0.8V achieving an efficiency of up to 70pJ/B in encryption, 50pJ/px in convolution, or up to 25MIPS/mW in software. As a strong argument for real-life flexible application of our platform, we show experimental results for three secure analytics use cases: secure autonomous aerial surveillance with a state-of-the-art deep convolutional neural network (CNN) consuming 3.16pJ per equivalent reduced instruction set computer operation, local CNN-based face detection with secured remote recognition in 5.74pJ/op, and seizure detection with encrypted data collection from electroencephalogram within 12.7pJ/op.

One of the main issues in the design of modern integrated circuits is power reduction. Mainly in digital circuits, the power consumption was defined by the dynamic power consumption, during decades. But in the new NanoCMOs technologies, the static power due to the leakage current is becoming the main issue in power consumption. As the leakage power is related to the amount of components, it is becoming mandatory to reduce the amount of transistors in any type of design, to reduce power consumption. So, it is important to obtain new EDA algorithms and tools to optimize the amount of components (transistors). It is also needed tools for the layout design automation that are able to design any network of components that is provided by an optimization tool that is able to reduce the size of the network of components. It is presented an example of a layout design automation tool that can do the layout of any network of transistors using transistors of any size. Another issue for power optimization is the use of tools and algorithms for gate sizing. The designer can manage the sizing of transistors to reduce power consumption, without compromising the clock frequency. There are two types of gate sizing, discrete gate sizing and continuous gate sizing. The discrete gate sizing tools are used when it is being used a cell library that has only few available sizes for each cell. The continuous gate sizing considers that the EDA tool can define any transistor sizing. In this case, the designer needs to have a layout design tool able to do the layout of transistors with any size. It will be presented the winner tools of the ISPD Contest 2012 and 2013. Also, it will be discussed the inclusion of our gate sizing algorithms in an industrial flow used to design state-of-the-art microprocessors. Another type of EDA tool that is becoming more and more useful is the visualization tools that provide an animated visual output of the running of EDA tools. This kind of tools is very usef- l to show to the tool developers how the tool is running. So, the EDA developers can use this information to improve the algorithms used in an EDA Tool.