Biblio
This work analyzed the coding gain that is provided in 6LoWPAN transceivers when channel-coding methods are used. There were made improvements at physical layer of 6LoWPAN technology in the system suggested. Performance analysis was performed using turbo, LDPC and convolutional codes on IEEE 802.15.4 standard that is used in the relevant physical layer. Code rate of convolutional and turbo codes are set to 1/3 and 1/4. For LDPC codes, the code rate is set as 3/4 and 5/6. According to simulation results obtained from the MATLAB environment, turbo codes give better results than LDPC and convolutional codes. It is seen that an average of 3 dB to 8 dB gain is achieved in turbo codes, in LDPC and convolutional coding, it is observed that the gain is between 2 dB and 6 dB depending on the modulation type and code rate.
This paper describes a realisation of a ResNet face recognition method through Zigbee-based wireless protocol. The system uses a CC2530 Zigbee-based radio frequency chip with connected VC0706 camera on it. The Arduino Nano had been used for organisation of data compression and effective division of Zigbee packets. The proposed solution also simplifies a data transmission within a strict bandwidth of Zigbee protocol and reliable packet forwarding in case of frequency distortion. The following investigation model uses Raspberry Pi 3 with connected Zigbee End Device (ZED) for successful receiving of important images and acceleration of deep learning interfaces. The model is integrated into a smart security system based on Zigbee modules, MySQL database, Android application and works in the background by using daemons procedures. To protect data, all wireless connections had been encrypted by the 128-bit Advanced Encryption Standard (AES-128) algorithm. Experimental results show a possibility to implement complex systems under restricted requirements of available transmission protocols.
Wireless Internet of Things (IoT) devices share several features such as limited energy supply, low computing power, limited memory size, and vulnerable radio communication network. IETF proposed the Constrained Application Protocol (CoAP) for this type of network. This paper presents implementation of CoAP into an embedded IoT device used for smart Energy Storage System (ESS) under microgrid environment. Confirmable message type was adopted to provide reliable communication. Since the frame size of IEEE 802.15.4 physical layer was limited to 127 bytes, the header of 6LoWPAN and UDP was compressed to reduce fragmentation and reassembly overhead. Performance of the communication service was tested by measuring round trip time between two end nodes of developed system.
This paper addresses the need for standard communication protocols for IoT devices with limited power and computational capabilities. The world is rapidly changing with the proliferation and deployment of IoT devices. This will bring in new communication challenges as these devices are connected to Internet and need to communicate with each other in real time. The paper provides an overview of IoT system architecture and the forthcoming challenges it will bring. There is an urging need to establish standards for communication in the IoT world. With the recent development of new protocols like CoAP, 6LowPAN, IEEE 802.15.4 and Thread in different layers of OSI model, additional challenges also present themselves. Performance and data management is becoming more critical than ever before due to the complexity of connecting raging number of IoT devices. The performance of the systems dealing with IoT devices will require appropriate capacity planning the associated development of data centers. Finally, the paper also presents some reasonable approaches to address the above issues in the IoT world.
Tactical wireless sensor networks (WSNs) are deployed over a region of interest for mission centric operations. The sink node in a tactical WSN is the aggregation point of data processing. Due to its essential role in the network, the sink node is a high priority target for an attacker who wishes to disable a tactical WSN. This paper focuses on the mitigation of sink-node vulnerability in a tactical WSN. Specifically, we study the issue of protecting the sink node through a technique known as k-anonymity. To achieve k-anonymity, we use a specific routing protocol designed to work within the constraints of WSN communication protocols, specifically IEEE 802.15.4. We use and modify the Lightweight Ad hoc On-Demand Next Generation (LOADng) reactive-routing protocol to achieve anonymity. This modified LOADng protocol prevents an attacker from identifying the sink node without adding significant complexity to the regular sensor nodes. We simulate the modified LOADng protocol using a custom-designed simulator in MATLAB. We demonstrate the effectiveness of our protocol and also show some of the performance tradeoffs that come with this method.
Internet into our physical world and making it present everywhere. This evolution is also raising challenges in issues such as privacy, and security. For that reason, this work is focused on the integration and lightweight adaptation of existing authentication protocols, which are able also to offer authorization and access control functionalities. In particular, this work is focused on the Extensible Authentication Protocol (EAP). EAP is widely used protocol for access control in local area networks such Wireless (802.11) and wired (802.3). This work presents an integration of the EAP frame into IEEE 802.15.4 frames, demonstrating that EAP protocol and some of its mechanisms are feasible to be applied in constrained devices, such as the devices that are populating the IoT networks.
This paper presents the relative merits of IR and microwave sensor technology and their combination with wireless camera for the development of a wall mounted wireless intrusion detection system and explain the phases by which the intrusion information are collected and sent to the central control station using wireless mesh network for analysis and processing the collected data. These days every protected zone is facing numerous security threats like trespassing or damaging of important equipments and a lot more. Unwanted intrusion has turned out to be a growing problem which has paved the way for a newer technology which detects intrusion accurately. Almost all organizations have their own conventional arrangement of protecting their zones by constructing high wall, wire fencing, power fencing or employing guard for manual observation. In case of large areas, manually observing the perimeter is not a viable option. To solve this type of problem we have developed a wall-mounted wireless fencing system. In this project I took the responsibility of studying how the different units could be collaborated and how the data collected from them could be further processed with the help of software, which was developed by me. The Intrusion detection system constitutes an important field of application for IR and microwave based wireless sensor network. A state of the art wall-mounted wireless intrusion detection system will detect intrusion automatically, through multi-level detection mechanism (IR, microwave, active RFID & camera) and will generate multi-level alert (buzzer, images, segment illumination, SMS, E-Mail) to notify security officers, owners and also illuminate the particular segment where the intrusion has happened. This system will enable the authority to quickly handle the emergency through identification of the area of incident at once and to take action quickly. IR based perimeter protection is a proven technology. However IR-based intrusion detection system is not a full-proof solution since (1) IR may fail in foggy or dusty weather condition & hence it may generate false alarm. Therefore we amalgamate this technology with Microwave based intrusion detection which can work satisfactorily in foggy weather. Also another significant arena of our proposed system is the Camera-based intrusion detection. Some industries require this feature to capture the snap-shots of the affected location instantly as the intrusion happens. The Intrusion information data are transmitted wirelessly to the control station via multi hop routing (using active RFID or IEEE 802.15.4 protocol). The Control station will receive intrusion information at real time and analyze the data with the help of the Intrusion software. It then sends SMS to the predefined numbers of the respective authority through GSM modem attached with the control station engine.