Biblio

The pre-magnetization of inertial confinement fusion capsules is a promising avenue for reaching hotspot ignition, as the magnetic field reduces electron thermal conduction losses during hotspot formation. However, in order to reach high yields, efficient burn-up of the cold fuel is vital. Suppression of heat flows out of the hotspot due to magnetization can restrict the propagation of burn and has been observed to reduce yields in previous studies [1] . This work investigates the potential suppression of burn in a magnetized plasma utilizing the radiation-MHD code ‘Chimera’ in a planar geometry.. This code includes extended-MHD effects, such as the Nernst term, and a Monte-Carlo model for magnetized alpha particle transport and heating. We observe 3 distinct regimes of magnetized burn in 1D as initial magnetization is increased: thermal conduction driven; alpha driven; and suppressed burn. Field transport due to extended-MHD is also observed to be important, enhancing magnetization near the burn front. In higher dimensions, burn front instabilities have the potential to degrade burn even more severely. Magneto-thermal type instabilities (previously observed in laser-heated plasmas [2] ) are of particular interest in this problem.

Contrary to previous opinion, ‘frost shattering’ is not the only major contributor to rock weathering at mid latitudes and high elevations, more specifically along edges of bedrock escarpments. Lightning is also a significant contributor to land surface denudation. We can show this as lightning strikes on outcrops can dramatically alter the magnetic signature of rocks and is one of the main sources of noise in paleomagnetic studies. Igneous rocks in the highlands of Lesotho, southern Africa (\textgreater 3000 m elevation) provide an ideal study location, as flow lavas remain as prominent ridges that are relatively resistant to weathering. It is well known that lightning strikes can cause large remanent magnetization in rocks with little resultant variation in susceptibility. At two adjoining peaks in the Lesotho highlands, mapped freshly fractured rock correlates with areas of high magnetic intensity (remanent component), but little variation in susceptibility (related to the induced field), and is therefore a clear indicator of lightning damage. The majority of these mapped strike sites occur at the edges of topographic highs. Variations in magnetic intensity are correlated with the much lower resolution national lightning strikes dataset. These data confirm that high elevation edges of peak scarps are the focus of previous lightning strikes. This method of magnetic surveying compared with lightning strike data is a new method of confirming the locations of lightning strikes, and reduces the need for intensive paleomagnetic studies of the area to confirm remanence.

This paper describes a prototype of a novel Permanent Magnetic Elastomer (PME) sheet based skin sensor for robotic applications. Its working principle is to use a Hall effect transducer to measure the change of magnetic field. PME is a polymer that has Neodymium particles distributed inside it, after strong magnetization for anisotropy, the PME acquires strong remanent magnetization that can be comparable to that of a permanent magnet, in this work, we made improvement of the strength of the magnetic field of PME, so it achieved magnetic strength as high as 25 mT when there is no deformation. When external forces apply on the sensor, the deformation of PME causes a change in the magnetic field due to the change in the alignment of the magnetic particles. Compared with other soft magnetic sensors that employ similar technology, we implemented linear regression method to simplify the calibration, so we focus on the point right above the magnetometer. An MLX90393 chip is installed at the bottom of the PME as the magnetometer. Experimental results show that it can measure forces from 0.01–10 N. Calibration is confirmed effective even for shear directions when the surface of PME is less than 15 x 15 mm.

A new methodology to calculate the hysteresis induced power loss of inductor from the measured waveforms of DC-to-DC converter during the voltage conversion is presented. From this study, we find that the duty cycles (D) of the buck and boost converters used till date for inductance current calculation are not exactly equal to VOUT/VIN and 1-VIN/VOUT as the inductance change induced by the hysteresis effect cannot be neglected. Although the increase in the loading currents of the converter increases the remanence magnetization of inductor at the turn-off time (toff), this remanence magnetization is destroyed by the turbulence induced vortex current at the transistor turn-on transient. So, the core power loss of inductor increases with the loading current of the converter and becomes much larger than other power losses and cannot be neglected for the power efficiency calculation during power stage design.

The use of AlNiCo alloys as the low coercive force (LCF) magnet in Variable Flux Memory Machines has been largely discussed in the literature, but similar magnetic materials as FeCrCo are still little explored. This paper proposes the study of a standstill magnetization strategy of a Variable Flux Memory Machine composed by a FeCrCo-based cylindrical rotor. An inverter in DC/DC mode is proposed for injecting short-time currents along the magnetization axis aiming the regulation of the magnetization state of the FeCrCo. A methodology for validating results obtained is defined from the estimation of the remanence and the excitation field characterizing the behavior of the internal recoil lines of the magnet used in the rotor. A study of the armature reaction affecting the machine when q-axis currents supply the machine is proposed by simulation.

Magnetized Liner Inertial Fusion (MagLIF) is a magneto-inertial fusion concept that relies on fuel magnetization, laser preheat, and a magnetically driven implosion to produce fusion conditions. In MagLIF, the target is a roughly 10 mm long, 5 mm diameter, 0.5 mm thick, cylindrical beryllium shell containing 1 mg/cm 3 D 2 gas. An axial magnetic field on the order of 10 T is applied to the target, and several kJ of laser energy is deposited into the fuel. Up to 20 MA of current is driven axially through the beryllium target, causing it to implode over approximately 100 ns. The implosion produces a 100-μm diameter, 8-mm tall fuel column with a burn-averaged ion temperature of several keV, that generates 10 11 -10 13 DD neutrons.

Magnetized Liner Inertial Fusion (MagLIF) is a magneto-inertial fusion (MIF) concept being studied on the Z-machine at Sandia National Laboratories. MagLIF relies on quasi-adiabatic heating of a gaseous deuterium (DD) fuel and flux compression of a background axially oriented magnetic field to achieve fusion relevant plasma conditions. The magnetic flux per fuel radial extent determines the confinement of charged fusion products and is thus of fundamental interest in understanding MagLIF performance. It was recently shown that secondary DT neutron spectra and yields are sensitive to the magnetic field conditions within the fuel, and thus provide a means by which to characterize the magnetic confinement properties of the fuel. 1 , 2 , 3 We utilize an artificial neural network to surrogate the physics model of Refs. [1] , [2] , enabling Bayesian inference of the magnetic confinement parameter for a series of MagLIF experiments that systematically vary the laser preheat energy deposited in the target. This constitutes the first ever systematic experimental study of the magnetic confinement properties as a function of fundamental inputs on any neutron-producing MIF platform. We demonstrate that the fuel magnetization decreases with deposited preheat energy in a fashion consistent with Nernst advection of the magnetic field out of the hot fuel and diffusion into the target liner.

Magnetic soft robots are increasingly popular as they provide many advantages such as miniaturization and tetherless control that are ideal for applications inside the human body or in previously inaccessible locations.While non-magnetic elastomers have been extensively characterized and modelled for optimizing the fabrication of soft robots, a systematic material characterization of their magnetic counterparts is still missing. In this paper, commonly employed magnetic materials made out of Ecoflex™ 00-30 and Dragon Skin™ 10 with different concentrations of NdFeB microparticles were mechanically and magnetically characterized. The magnetic materials were evaluated under uniaxial tensile testing and their behavior analyzed through linear and hyperelastic model comparison. To determine the corresponding magnetic properties, we present a method to determine the magnetization vector, and magnetic remanence, by means of a force and torque load cell and large reference permanent magnet; demonstrating a high level of accuracy. Furthermore, we study the influence of varied magnitude impulse magnetizing fields on the resultant magnetizations. In combination, by applying improved, material-specific mechanical and magnetic properties to a 2-segment discrete magnetic robot, we show the potential to reduce simulation errors from 8.5% to 5.4%.

This paper deals with electromagnetic vibration excitation of rotating machine blades in a purpose of dynamic measurement and testing. A novel method for increasing the excitation force is presented. At the same time, the suggested method allows to reduce blade remanent induction. Examples of measurements are shown, and obtained results are discussed.

In this paper, we present a study about the remanence state and coercivity in 1-D chain of cobalt hollow nanospheres, by using micromagnetic simulation. The high coercivity values (Hc is determined in the range of 600-1800 Oe) and the monotonic decrease of remanence are attributed to the shape anisotropy effect due to an increase in the aspect ratio value. The configuration of magnetization in remanence showed the onion state for hollow spheres (HSs) with Re = 15 nm, whereas for Re = 30 nm, appear the curling-vortex (CV) state. Finally for a cluster of chains, constituted by cobalt HSs, with random orientations the CV state is preserved.

In this paper, a transformer model has been developed. The model is based on the equivalent electrical circuit used in transient simulation studies which considers the non-linearity of the iron core. The non-linear ferromagnetic behavior of the iron core was obtained by using the Jiles-Atherton hysteresis model. The magnetizing inrush current of a core type single-phase transformer was analyzed under four different energization conditions. The primary winding of the transformer was connected to the supply at various instants while there was either some level of remanent flux or no remanent flux in the iron core. Corresponding simulation results are presented and discussed.

Reliable calculation model of electromagnetic mechanism characteristics of DC contactor is of great significance to its structural optimization. In this paper, the excitation process of contactor magnet is summarized, and a new calculation model of hysteresis-finite element method is proposed. It can effectively calculate the remanence of the electromagnetic mechanism under different excitation conditions, and give the relationship curve between the remanence flux and the anti-remanence gap.

A Stoner-Wohlfarth-type model is used to demonstrate the effect of the buildup of magnetic charges near the grain boundaries of low anisotropy polycrystalline materials, revealed by measuring the magnetization during positive-field warming after negative-field cooling. The remnant magnetization after negative-field cooling has two different contributions. The temperature-dependent component is modeled as an assembly of particles with thermal relaxation. The temperature-independent component is modeled as an assembly of particles overcoming variable phenomenological energy barriers corresponding to the change in susceptibility when the anisotropy constant changes its sign. The model is applicable to soft-magnetic materials where the buildup of the magnetic charges near the grain boundaries creates demagnetizing fields opposing, and comparable in magnitude to, the anisotropy field. The results of the model are in qualitative agreement with published data revealing the magneto-thermal characteristics of polycrystalline gadolinium.

The goal of this paper is to simulate the interactions between magnetic objects in a physically correct way. The simulation scheme is based on magnetization dynamics, which describes the temporal change of magnetic moments. For magnetization dynamics, the Landau-Lifshitz-Gilbert equation is adopted, which is widely used in micromagnetics. Through effectively-designed novel models of magnets, it is extended into the macro scale so as to be combined with real-time rigid-body dynamics. The overall simulation is stable and enables us to implement mutual induction and remanence that have not been tackled by the state-of-the-art technique in magnet simulation. The proposed method can be applied to various fields including magnet experiments in the virtual world.

Micromagnetic simulations of coercivity as a function of external magnetic field direction were performed for a hexagonal array of hemispherical Permalloy nanocaps. The analysis was based on hysteresis loops for arrangements of nanocaps of variable thickness (5 nm and 10 nm). The angular dependence of coercivity had a maximum at about 80° with respect to the arrangement plane. An increase in coercivity with nanocap thickness is related to the magnetization reversal mechanism, where the dipole energy of individual caps generates an effective intermediate axis, locking the magnetic moments. The coercivity has maximum values of 109 Oe for 5 nm and 156 Oe for 10 nm thickness. The remanence decreases monotonically with angle. This is associated with the influence of shape anisotropy, where the demagnetizing field in the plane of the array is much smaller than the demagnetizing field perpendicular to the plane.

We report time-domain measurements of acoustic-wave-induced magnetization dynamics in magnetic tunnel junctions. The acoustic pulses are generated by femtosecond laser excitation and interact with the magnetization through magnetoelastic coupling. The induced magnetization precession is not only dependent on the externally applied magnetic field, but also on the laser excitation position. The presented method even allows us to coherently control the precession using two laser pulses at various magnetic fields and excitation positions.

Various critical state models have been developed to understand the hysteresis loss mechanism of high-temperature superconducting (HTSC) films. The analytic relation between the hysteresis loss and the remanent field was obtained based on Bean's critical state model for thin films in the full-penetration case. Furthermore, numerical calculation of local hysteresis loops was carried out by Kim's critical state model. In this paper, we investigated local hysteresis losses for a GdBCO coated conductor by using low-temperature scanning Hall probe microscopy and reproduced the experimental results by applying the critical state model. Because of the demagnetizing effect in thin films, analysis of local hysteresis losses can be useful approach to understand of total hysteresis losses.

We demonstrate how a unique nanomodulation within a continuous ferromagnetic film can induce magnetic dipoles at predefined, submicrometer scale locations, which can tune the global magnetic properties of the film due to dipole-dipole interactions. Arrays of tunable magnetic dipoles are generated with in-plane and out-of-plane directions, which can be rotated in-plane within the three-dimensional (3-D) modulated structure of a continuous film. In-plane magnetic dipole rotation enables a methodology to control overall magnetic properties of a ferromagnetic thin film. Formation of magnetic dipoles and their tunability were studied in detail by magnetic force microscopy, high-resolution magnetic measurements, and micromagnetic simulation of a nanomodulated Ni45Fe55 alloy film. A pattern larger than a single magnetic domain would normally form a vortex in the remanent state. However, here the unique 3-D nanostructure prevents vortex formation due to the competition between in-plane and out-of-plane dipole-dipole interaction giving rise to a metastable state. Experimentally, at zero remanence, the magnetization goes through a transformation from a metastable to a stable state, where the dipole-dipole interaction depends on their geometrical arrangement. Thus, the magnetic properties of the continuous film can be varied by the proposed pattern geometry. A detail analytical study of the dipolar energy for the system agrees well with the experimental and simulated results.

A significant advance in magnetic field management in a fully assembled superconducting radiofrequency cryomodule has been achieved and is reported here. Demagnetization of the entire cryomodule after assembly is a crucial step toward the goal of average magnetic flux density less than 0.5 μT at the location of the superconducting radio frequency cavities. An explanation of the physics of demagnetization and experimental results are presented.

The MgO-based magnetic tunnel junction (MTJ) is the basis of modern hard disk drives' magnetic read sensors. Within its operating bandwidth, the sensor's performance is significantly affected by nonlinear and oscillating behavior arising from the MTJ's magnetization dynamics at microwave frequencies. Static I-V curve measurements are commonly used to characterize sensor's nonlinear effects. Unfortunately, these do not sufficiently capture the MTJ's magnetization dynamics. In this paper, we demonstrate the use of the two-tone measurement technique for full treatment of the sensor's nonlinear effects in conjunction with dynamic ones. This approach is new in the field of magnetism and magnetic materials, and it has its challenges due to the nature of the device. Nevertheless, the experimental results demonstrate how the two-tone measurement technique can be used to characterize magnetic sensor nonlinear properties.

This paper design three distribution devices for the strong and smart grid, respectively are novel transformer with function of dc bias restraining, energy-saving contactor and controllable reactor with adjustable intrinsic magnetic state based on nanocomposite magnetic material core. The magnetic performance of this material was analyzed and the relationship between the remanence and coercivity was determined. The magnetization and demagnetization circuit for the nanocomposite core has been designed based on three-phase rectification circuit combined with a capacitor charging circuit. The remanence of the nanocomposite core can neutralize the dc bias flux occurred in transformer main core, can pull in the movable core of the contactor instead of the traditional fixed core and adjust the saturation degree of the reactor core. The electromagnetic design of the three distribution devices was conducted and the simulation, experiment results verify correctness of the design which provides intelligent and energy-saving power equipment for the smart power grids safe operation.

Arrays of nanosized hollow spheres of Ni were studied using micromagnetic simulation by the Object Oriented Micromagnetic Framework. Before all the results, we will present an analysis of the properties for an individual hollow sphere in order to separate the real effects due to the array. The results in this paper are divided into three parts in order to analyze the magnetic behaviors in the static and dynamic regimes. The first part presents calculations for the magnetic field applied parallel to the plane of the array; specifically, we present the magnetization for equilibrium configurations. The obtained magnetization curves show that decreasing the thickness of the shell decreases the coercive field and it is difficult to obtain magnetic saturation. The values of the coercive field obtained in our work are of the same order as reported in experimental studies in the literature. The magnetic response in our study is dominated by the shape effects and we obtained high values for the reduced remanence, Mr/MS = 0.8. In the second part of this paper, we have changed the orientation of the magnetic field and calculated hysteresis curves to study the angular dependence of the coercive field and remanence. In thin shells, we have observed how the moments are oriented tangentially to the spherical surface. For the inversion of the magnetic moments we have observed the formation of vortex and onion modes. In the third part of this paper, we present an analysis for the process of magnetization reversal in the dynamic regime. The analysis showed that inversion occurs in the nonhomogeneous configuration. We could see that self-demagnetizing effects are predominant in the magnetic properties of the array. We could also observe that there are two contributions: one due to the shell as an independent object and the other due to the effects of the array.