Biblio

This paper presents a study and analysis of flux linkage performance on 12/8 pole doubly salient permanent magnet machine in square envelope conventional. Analyzed model was using a finite element method. The investigated model was constructed by changing the size of the structure as the main parameters of the speed 500 rpm, PM coercivity 910 kA/m, PM remanence 1.2 T, copper loss 30 W, turns per coil 45, and stator side length 100 mm. The study and analysis of flux linkage, induced voltage, and torque are also included in this paper.

Interface transformer used in asynchronous networking was a kind of special transformer which's different from normal power transformer. During no-load switch-in, the magnitude of inrush current will be high, and the waveform distortion also be severity. Maybe the protections will be activated, even worse may lead the lockdown of the DC system. In this paper, field-circuit coupled finite element method was used for the study of transient characteristic of no-load switch-in, remanence simulation methods were presented. Quantitative analysis of the effect of closing making angle and core remanence on inrush current peak value, meanwhile, the distribution of magnetic field inside the tank during the transient process. The result indicated that the closing making angle and core remanence have obvious effect on inrush current peak value. The research results of this paper can be used to guide the formulation of no-load switch-in strategy of interface transformer, which was of great significance to ensure the smooth operation of HVDC Flexible system.

Novel magneto-optical isolator and self-holding optical switch with an a-Si:H microring resonator are demonstrated. The devices are driven by the remanence of integrated thin-film magnet and, therefore, maintain their state without any power supply.

This paper presents the development of a control circuit to enhance the performances of LED lamps. In this direction, a comparison between the luminous intensity of normal LED based lamps and mid-power ones, for both continuous and switching conditions has been made. The already well know control technologies were analyzed and a study was conducted to increase the lighting performances by rising the operating frequency and magnifying the contribution of remanence effect and thus increasing the efficiency of the light source. To achieve this, in the first stage of the project the power and control circuits have been modeled, related to desired parameters and tested in simulation software. In the second stage, the proposed circuit was implemented by functional blocks and in the last stage, tests were made on the circuit and on light sources in order to process the results. The power consumption has been decreased nearly to a half of it and the luminous flux raised with 15% due to overcurrent and remanence effect that we used.

This research paper presented a design that will address the challenges brought by remanence in ground-fault current interrupter devices (gfci). Remanence or residual magnetism is the magnetization left behind in a ferromagnetic material (such as iron) after an external magnetic field is removed. Remanence will make the gfci devices less accurate and less reliable in tripping the current above threshold in just five (5) years. It affects the performance of the device in terms of efficiency, accuracy, and response time. In this research, the problems caused by remanence were alleviated by using two identical transformers in detecting residual current both for hot and neutral wires. The difference of the current detected by the two transformers will be the basis of the signal threshold in tripping the device. By doing so, the problems caused by remanence phenomenon will be solved without compromising the response time of the circuit which is around 16 mS. The design will extend the life span of GFCI devices up to 15 years.

This paper deals with electromagnetic vibration excitation of rotating machine blades in a purpose of dynamic measurement and testing. A novel method for increasing the excitation force is presented. At the same time, the suggested method allows to reduce blade remanent induction. Examples of measurements are shown, and obtained results are discussed.

The relationship between magnetic domain structures and magnetic properties of Nd-doped Sm(Fe, Cu, Zr, Co)7.5 was investigated. In the preparation process, slow cooling between sintering and solution treatment was employed to promote homogenization of microstructures. The developed magnet achieved a maximum energy product, [BH]m, of 33.8 MGOe and coercivity, Hcb, of 11.2 kOe at 25 °C, respectively. Moreover, B-H line at 150 °C was linear, which means that irreversible demagnetization does not occur even at 150 °C. Temperature coefficients of remanent magnetic flux density, Br, and intrinsic coercivity, Hcj, were 0.035%/K and 0.24%/K, respectively, as usual the conventional Sm-Co magnet. Magnetic domain structures were observed with a Kerr effect microscope with a magnetic field applied from 0 to -20 kOe, and then reverse magnetic domains were generated evenly from grain boundaries. Microstructures referred to as “cell structures” were observed with a scanning transmission electron microscope. Fe and Cu were separated to 2-17 and 1-5 phases, respectively. Moreover, without producing impurity phases, Nd showed the same composition behavior with Sm in a cell structure.

Hexagonal CdS and Fe-doped CdS nanorods were synthesised by a facile hydrothermal method and characterised by X-ray diffraction, energy dispersive X-ray spectroscopy, UV-vis absorption, photoluminescence, and X-ray photoelectron spectroscopy. The magnetic properties of undoped and Fe-doped CdS nanorods were investigated at room temperature. The experimental results demonstrate that the ferromagnetism of the Fe-doped CdS nanorods differs from that of the undoped CdS nanorods. The remanence magnetisation (Mr) and the coercive field (Hc) of the Fe-doped CdS nanorods were 4.9 × 10-3 emu/g and 270.6 Oe, respectively, while photoluminescence properties were not influenced by doping. First-principle calculations show that the ferromagnetism in Fe-doped CdS nanocrystal arose not only from the Fe dopants but also from the Cd vacancies, although the main contribution was due to the Fe dopants.

We report on the significant enhancement of perpendicular magnetic anisotropy of Ni/NiO multilayers after mild annealing up to 90 min at 250 °C. Transmission electron microscopy shows that after annealing, a partial crystallization of the initially amorphous NiO layers occurs. This turns out to be the source of the anisotropy enhancement. Magnetic measurements reveal that even multilayers with Ni layers as thick as 7 nm, which in the as-deposited state showed inplane anisotropy with square hysteresis loops, show reduced in-plane remanence after thermal treatment. Hysteresis loops recorded with the field in the normal-to-film-plane direction provide evidence for perpendicular magnetic anisotropy with up and down magnetic domains at remanence. A plot of effective uniaxial magnetic anisotropy constant times individual Ni layer thickness as a function of individual Ni layer thickness shows a large change in the slope of the data attributed to a drastic change of volume anisotropy. Surface anisotropy showed a small decrease because of some layer roughening introduced by annealing.

Datasheets of different commercially available integrated sensors for vector measurements of magnetic fields provide typical specifications, such as measurement range, sampling rate, resolution, and noise. Other characteristics of interest, such as linearity, cross-sensitivity, remanent magnetization, and drifts over temperature, are mostly missing. This letter presents testing results of those characteristics of integrated three-dimensional (3-D) sensors working with different sensor principles and technologies in a reproducible measuring process. The sensors are exposed to temperatures from -20 °C to 80 °C and are cycled in hysteresis loops in fields up to 2.5 mT. For applying high-accuracy magnetic fields, a calibrated 3-D Helmholtz coil setup is used. Commercially available integrated 3-D magnetic field sensors are put in operation on a printed circuit board using nonmagnetic passive components. All sensors are configured for best measurement accuracy according to their data-sheets. The results show that sensors based on anisotropic magnetoresistance have high accuracy and low offsets yet also a high degree of nonlinearity. Hall-based sensors show good linearity but also high cross-sensitivity. A magnetic remanence appears for Hall-based sensors with integrated magnetic concentrators as well as for sensors using anisotropic magnetoresistance. Nearly all sensors show remaining drifts over temperature regarding offset and sensitivity up to several percentages.

The relationship between integrated media noise power and linear density in heat-assisted magnetic recording (HAMR) is discussed. A noise plateau for intermediate recording density has been observed in HAMR, similar to that found in perpendicular magnetic recording (PMR). Here, we show, by changing the temperature profile of the heat spot in HAMR, that we can tune the noise plateau regions to different recording densities. The heat spot with sharp temperature gradient favors a plateau at high recording density, while the heat spot with gradual temperature gradient favors a plateau at low recording density. This effect is argued to be a consequence of the competition between transition noise and remanence noise in HAMR.

In this paper, we present a study about the remanence state and coercivity in 1-D chain of cobalt hollow nanospheres, by using micromagnetic simulation. The high coercivity values (Hc is determined in the range of 600-1800 Oe) and the monotonic decrease of remanence are attributed to the shape anisotropy effect due to an increase in the aspect ratio value. The configuration of magnetization in remanence showed the onion state for hollow spheres (HSs) with Re = 15 nm, whereas for Re = 30 nm, appear the curling-vortex (CV) state. Finally for a cluster of chains, constituted by cobalt HSs, with random orientations the CV state is preserved.

Influence of remanent flux on hysteresis curve of the transformer core is addressed in this paper. In addition, its significant negative effect on transformer diagnostic tests is quantified based on experimental studies. Furthermore, a novel approach is proposed to efficiently and quickly eliminate the remanent flux. This approach is evaluated based on simulation studies on a 230/63-kV power transformer. Meanwhile, experimental studies are performed on both 0.2/0.2 and 20/0.4 kV transformers. These studies reveal that the approach not only is well able to eliminate the remanent flux, but also it has various advantages over the commonly used method. In addition, this approach is equally applicable for various power, distribution, and instrument transformer types.

In this letter, ferroelectric memory performance of TiN/Y-doped-HfO2 (HYO)/TiN capacitors is investigated under proton radiation with 3-MeV energy and different fluence (5e13, 1e14, 5e14, and 1e15 ions/cm2). X-ray diffraction patterns confirm that the orthorhombic phase Pbc21 of HYOfilm has no obvious change after proton radiation. Electrical characterization results demonstrate slight variations of the permittivity and ferroelectric hysteresis loop after proton radiation. The remanent polarization (2Pr) of the capacitor decreases with increasing proton fluence. But the decreasing trend of 2Pr is suppressed under high electric fields. Furthermore, the 2Pr degradation with cycling is abated by proton radiation. These results show that the HYO-based ferroelectric memory is highly resistive to proton radiation, which is potentially useful for space applications.

Macroscopic hysteresis loops and microscopic magnetic moment distributions have been determined by 3-D model for Co nanowire with various easy axis deviations from applied field. It is found that both the coercivity and the remanence decrease monotonously with the increase of easy axis deviation as well as the maximum magnetic product, indicating the large impact of the easy axis orientation on the magnetic performance. Moreover, the calculated angular distributions and the evolution of magnetic moments have been shown to explain the magnetic reversal process. It is demonstrated that the large demagnetization field in the two ends of the nanowire makes the occurrence of reversal domain nucleation easier, hence the magnetic reversal. In addition, the magnetic reversal was illustrated in terms of the analysis of the energy evolution.

High-temperature magnetic properties of the anisotropic bulk SmCo7/Fe(Co) nanocomposite magnets prepared by multistep deformation have been investigated and compared with the corresponding isotropic nanocomposites. The anisotropic SmCo7/Fe(Co) nanocomposites with a Fe(Co) fraction of 28% exhibit much higher energy products than the corresponding isotropic nanocomposites at both room and high temperatures. These magnets show a small remanence (α = -0.022%/K) and a coercivity (β = -0.25%/K) temperature coefficient which can be comparable to those of the conventional SmCo5 and Sm2Co17 high-temperature magnets. The magnetic properties of these nanocomposites at high temperatures are sensitive to the weight fractions of the Fe(Co) phase. This paper demonstrates that the anisotropic bulk SmCo7/Fe(Co) nanocomposites have better high-temperature magnetic properties than the corresponding isotropic ones.

This paper proposes a novel kind of direct-current and alternate-decay-current hybrid integrative magnetization and demagnetization power supplies applied to transformer dc bias treatment based on a nanocomposite magnetic material. First, according to the single-phase transformer structure, one dc bias magnetic compensation mechanism was provided. The dc bias flux in the transformer main core could be eliminated directionally by utilizing the material remanence. Second, for the rapid response characteristic of the magnetic material to an external magnetic field, one positive and negative dc magnetization superimposed decaying ac demagnetization hybrid integrative power supplies based on single-phase rectifier circuit and inverter circuit was designed. In order to accurately control the magnetic field strength by which a good de/-magnetization effect could be achieved, this paper adopts the double-loop control technology of the magnetic field strength and magnetizing current for the nanocomposite magnetic state adjustment. Finally, two 10 kVA transformers and the experiment module of the hybrid integrative power supplies were manufactured and built. Experimental results showed that the integrated power supplies have good de/-magnetization effect and practicability, proving the validity and feasibility of the proposed scheme.

The discovery of the interstitial rare earth nitride Sm2Fe17N3 came about seven years after the discovery of the rare earth iron boride Nd2Fe [1],[2], and the nitride initially seemed to offer intrinsic magnetic properties that were superior (Curie temperature TC, magnetocrystalline anisotropy K1 or comparable (spontaneous magnetization Ms to those of its illustrious predecessor. However, the promise of the new material to seriously challenge Nd2Fe14B was not realized. The 2:17 nitride powder, prepared by a low-temperature gas-phase interstitial modification process proved difficult to orient and worse still, it lost its nitrogen at the temperatures needed to process dense sintered magnets [3]. Attempts at explosive compaction [4] or spark sintering [5] failed to yield material with good enough coercivity. Nevertheless, work continued in Japan and China to develop a coercive powder that could be used for bonded magnets. An early realization was zinc-bonded Sm2Fe17N3 [6] with an energy product of 84 kJm3 but a rather low coercivity of 480 kAm-1, less than 5 % of the anisotropy field (Ha = 2K1/Ms ≈ 11 MAm-1). The anisotropy field of Nd2Fe14B is significantly less (6 MAm-1) yet several decades of intensive development have led to higher values and continuous improvements of the coercivity, even in unsubstituted material. Historical experience with permanent magnets shows that a long period of materials development is needed to arrive at the best composition and processing conditions for a microstructure that allows the hard magnetism to be optimized. Coercivities of about 25% of the anisotropy field are ultimately achieved. Here we compare the magnetic properties of melt-spun material. Our Nitroquench powder, produced by Daido Steel, was in the form of flakes 10 μm thick and up to 100 μm in diameter. A crystal-lite size of approximately 15 nm deduced from Scherrer broadening of the X-ray reflections. Composition was checked by EDX microprobe analysis. Hysteresis loops have been measured in applied fields of up to 14 T, at room temperature and at 4 K.The material exhibits a room-temperature coercivity of 690 kAm-1 after saturation in 14 T, with a remanence of 700 kAm-1 in zero applied field and an extrapolated saturation magnetization of 1230 kAm-1. The remanence ratio Mr/Ms of 63% when the remanence is corrected to zero internal field, is reflected in a preferred orientation seen in the X-ray powder diffraction patterns and in 57Fe Mössbauer spectra of magnetized powder. Spectra obtained after saturation of an immobilized powder absorber either in-plane or perpendicular to the sample plane exhibit distinctly different relative intensities of the ΔM=0 absorption lines. The maximum energy product for the powder, assuming full density, is 162 kJm-3. The remanence enhancement is attributed to fact that the nanocrystallite size is not much greater than the exchange length. Melt-spun Sm-Fe-N powder has superior corrosion resistance and thermal stability compared to melt-spun Nd-Fe-B. The Nitroquench powder may be used to produce polymer-bonded magnets with an energy product in excess of 100 kJm-3.

Protection of secured data content in volatile memories (processor caches, embedded RAMs etc) is essential in networking, wireless, automotive and other embedded secure applications. It is utmost important to protect secret data, like authentication credentials, cryptographic keys etc., stored over volatile memories which can be hacked during normal device operations. Several security attacks like cold boot, disclosure attack, data remanence, physical attack, cache attack etc. can extract the cryptographic keys or secure data from volatile memories of the system. The content protection of memory is typically done by assuring data deletion in minimum possible time to minimize data remanence effects. In today's state-of-the-art SoCs, dedicated hardwares are used to functionally erase the private memory contents in case of security violations. This paper, in general, proposes a novel approach of using existing memory built-in-self-test (MBIST) hardware to zeroize (initialize memory to all zeros) on-chip memory contents before it is being hacked either through different side channels or secuirty attacks. Our results show that the proposed MBIST based content zeroization approach is substantially faster than conventional techniques. By adopting the proposed approach, functional hardware requirement for memory zeroization can be waived.

In this paper, a transformer model has been developed. The model is based on the equivalent electrical circuit used in transient simulation studies which considers the non-linearity of the iron core. The non-linear ferromagnetic behavior of the iron core was obtained by using the Jiles-Atherton hysteresis model. The magnetizing inrush current of a core type single-phase transformer was analyzed under four different energization conditions. The primary winding of the transformer was connected to the supply at various instants while there was either some level of remanent flux or no remanent flux in the iron core. Corresponding simulation results are presented and discussed.

Back-end-of-line compatible integration of NdFeB-based micro magnets onto 8 inch Si substrates is presented. Substrate conditioning procedures to enable further processing in a cleanroom environment are discussed. It is shown that permanent magnetic structures with lateral dimensions between 25μm and 2000μm and a depth up to 500μm can be fabricated reliably and reproducibly with a remanent magnetization of 340mT at a standard deviation as low as 5% over the substrate. To illustrate post-processing capabilities, the fabrication of micro magnet arrangements embedded in silicon frames is described.

Tensile residual stresses combined with an applied tensile stress can reduce the reliability of steel components. Nondestructive evaluation of residual stress is thus important to avoid unintended fatigue or cracking. Because magnetic hysteresis properties of ferromagnetic materials are sensitive to stress, nondestructive evaluation of residual stress through magnetic properties can be expected. The spatial mapping of local magnetic hysteresis properties becomes possible by using the acoustically stimulated electromagnetic (ASEM) method and the tensile stress dependence of the hysteresis properties has been investigated in steel. It is found that the coercivity Hc and the remanent magnetization signal Vr monotonically decrease with increasing the tensile stress. In this work, we verified the detection of residual stresses through the ASEM response in a welded steel plate. Tensile stresses are intentionally introduced on the opposite side of the partially welded face by controlling welding temperatures. We found that Hc and Vr clearly decrease in the welded region, suggesting that the presence of tensile residual stresses is well detected by the hysteresis parameters.

Very sensitive magnetic instruments on the JUICE spacecraft require an extremely low magnetic field emission of the various subsystems. The JUICE solar array includes a photovoltaic assembly and various mechanisms with a magnetic signature. The design of the photovoltaic assembly has been optimised not only with respect to magnetic moment, but also with respect to the emitted magnetic field, by applying the so-called back-wiring technique, alternating string polarity etc. The remanent magnetic field of the mechanisms (hinges, eddy-current damper, hold-down & release mechanism) was tested including a process for demagnetisation. In addition, the temperature coefficient for the magnetic moment was measured, down to the operational temperature of -130°C. The eddy-current damper was also subjected to a field-induced magnetisation test. All the contributors were included in a model to calculate the magnetic field at the instrument location.

This paper investigates the temperature demagnetization modeling method for permanent magnets (PM) in permanent magnet synchronous linear motor (PMSLM). First, the PM characteristics are presented, and finite element analysis (FEA) is conducted to show the magnetic distribution under different temperatures. Second, demagnetization degrees and remanence of the five PMs' experiment sample are actually measured in stove at temperatures varying from room temperature to 300 °C, and to obtain the real data for next-step modeling. Third, machine learning algorithm called extreme learning machine (ELM) is introduced to map the nonlinear relationships between temperature and demagnetization characteristics of PM and build the demagnetization models. Finally, comparison experiments between linear modeling method, polynomial modeling method, and ELM can certify the effectiveness and advancement of this proposed method.

This paper presents a new class of high-performance permanent micro-magnets based on the controlled assembly of cobalt nanorods for the electromagnetic transduction of MEMS. Micromagnets are fabricated using a low temperature fabrication process that yields a dense material exhibiting high coercive field and remanence to saturation magnetization ratio. The cartography of the magnetic induction produced by the sub-millimeter size magnets was obtained using a scanning Hall effect micro-probe microscope. Silicon microcantilevers placed in the vicinity of these magnets were successfully actuated using the Lorentz force with low currents. The good signal to noise ratio measured at resonance demonstrates the potentiality of these nanostructured micro-magnets.